Voltage stabilizers Teplokom for gas boilers

Gas type boilers control fuel consumption, water flow rate. The devices consist of microprocessors, pumps, programmers, which function normally only with a sinusoidal voltage. The reliable stabilizer Bastion for a gas boiler meets the specifics of the domestic power line, provides high-quality power supply to all elements of the system.

Technical characteristics of the stabilizer Teplokom

Stabilization devices are available in the Teplocom and SKAT ST series. The Teplokom line is equipped with a microprocessor and has a wide input voltage range.

Relay devices have the following technical parameters:

• voltage equalization up to 220-240 V, subject to network fluctuations of 145-260 V;
• work in the temperature range from -10 to +40 degrees;
• the output voltage waveform is pure sine;
• power rating - 400 VA;
• maximum power - from 500 to 1300 VA;
• moisture protection class IP-20;
• the ability to operate at an air humidity of 80%.

The fuse is produced in a white plastic case, is a volatile device with protection against overloads, short circuits, and is equipped with a noise filtering system.

The principle of operation of stabilizers

The Teplocom stabilizer is used in order to equalize the power supply of equipment with a total absorption power of up to 800 VA. Uninterruptible voltage sources are advisable in case of constant rolling blackouts, low mains voltage or overvoltage. The devices ensure the autonomy of the gas boiler in the event of a power outage.

The UPS equalizes the output voltage in the range of 220 V, if external 135-270 V is supplied. If these indicators are exceeded, an automatic shutdown is triggered. After the output power returns to the operating range, the device will turn on again.

Protective systems keep stabilizers in case of line failure. They function autonomously. Also, the devices of the "Bastion" holding are automatically turned off in case of overheating.

Information about the voltage at the input / output is displayed on the display.

UPS characteristics

The relay stabilizer reacts to voltage parameters and equalizes it to the desired limit. The device is necessary for the following reasons:

• in case of failure, an imported gas boiler that is not connected to an uninterruptible power supply will have to be replaced, which involves financial costs;
• with voltage fluctuations, the service life of boiler equipment and pumps is reduced;
• a sudden shutdown of the heating system will lead to further breakdowns in communications.

The Teplokom stabilizer is a modern device with many functions.

Easy and convenient connection

Gas boilers are phase-dependent equipment, therefore, the manufacturer's instructions are needed to connect the UPS. It indicates a step-by-step work algorithm:

1. Connect the power plug of the stabilizer to a 220 V socket.
2. Wait for the "Network" indicator to appear.
3. After 5-10 minutes, the device will start working.

Once every 6 months, you will need to wipe off the dust, check the performance of the product and the integrity of the contacts.

The power output of Bastion equipment must not be less than the total power consumption of the boiler.

Miniature dimensions

You can choose a voltage stabilizer of the Teplocom series for floor and wall gas boilers. Depending on the model, the parameters of width, depth and height differ:

• ST 222/500 - 104x104x135 mm;
• ST 555 - 130x170x85 mm;
• ST 888 and ST 1515 - 169x210x101 mm;
• ST 400 and 600 Invertor - bass reflex, 242x170x98 mm;
• ST-1000 and ST-1500 - 305x171x128 mm;
• ST-1300 - 322x220x134 mm.

The devices are designed for voltages from 222 to 1515 VA and comply with GOST 14254-2015.

Protection against voltage fluctuations, lightning and network accidents

Under normal voltage conditions, the transformer will oscillate +/- 15 V. If there is 220 V in the network, the voltage immediately goes to the consumer, has a transformation ratio of 1. In the range of 205-235 V, the output voltage does not change. When racing, the following happens:

• less than 205 V - the secondary winding is activated with a factor of 1.75. The tap is closed, the current flows to the output contacts;
• above 235 V - the secondary winding is activated, the transformation ratio of which is 0.94. The voltage is leveled to 220 V.

The system of protection against accidents is implemented:

• With the help of the thresholds for surge and sagging of the current at the output, the load is turned off in a few seconds. When the parameters are normalized, the voltage of the fuse works again.
• Bypass - voltage is supplied bypassing the circuit, the malfunction can be eliminated without turning off the boiler.

In the event of a lightning strike, the thermal protection system operates - the UPS is not powered until the winding transformers have cooled down.

High overload capacity limit

Large overload power ensures the use of uninterruptible power supplies in conjunction with equipment, which is characterized by a high starting current. The device can be installed indoors, connected to wall-mounted and floor-standing boilers with an open or closed combustion chamber.

Advantages and disadvantages

Relay stabilizers from Teplokom differ in a number of advantages:

• inexpensive price with a long service life;
• operation at input voltage range 140-290 V;
• response speed from 100 to 200 V / sec;
• small size and light weight;
• connection to equipment with no load;
• microprocessor-based type of control, providing switching of the windings when crossing zero;
• minimal contact wear;
• the presence of several degrees of protection - from power surges, emergency situations on the line, high-frequency interference, weather factors.

The disadvantages of relay modifications include the service life depending on the build quality, the impossibility of using it for lighting systems. The uninterruptible power supply can click loudly at the moment the protection is triggered.

Operating rules

When using Teplocom stabilization devices, a 2-5 year warranty must be taken into account, provided that the requirements are met. The manufacturer notes the basic requirements for operation:

• The power of the equipment is selected according to the parameters of the mains voltage.
• Installation is possible only in a dry room, without current dust and vapors of household chemicals.
• The stabilizer works in an open area, it is not placed in a cabinet, niche or cabinet.
• The working temperature of the device for indoor use should be in the range from +5 to -40 degrees.

The entire line of the brand is connected to the power grid using a plug. A socket is used for connection to the boiler.

The nuances of choosing stabilizers Teplokom

When buying a device, you need to take into account the quality of the output current, power, response speed, voltage indicators at the input and output. The sine wave for a quality signal should be almost perfect. The Teplocom range is suitable for all heating boilers, since it does not change the direction of the current in the network. The selection of the device is carried out taking into account the following factors:

• The electrical power must be 30% higher than the boiler power.
• The presence of circulating sediment. Power is calculated using the formula, Vtot = 1.3 x (V1 + V2 ∙ 3), where: V1 - boiler power, VA. V2 is the power of the circulation pump, VA.3 - coefficient of accounting for voltage fluctuations at the time of starting the pump, 1.3 - power safety factor.
• Response time. For gas boilers, fuses with a shorter response time and a faster voltage equalization rate are suitable.
• Input voltage parameters. Devices with a minimum input range are not suitable for low voltage networks.
• Deviation from the output current. The range for a 220 V network should be minimal.

The simplest heating equipment can withstand a deviation of up to 10%, models with automation - up to 5%.

Stabilizers by Teplokom are suitable for imported and Russian gas boilers. The manufacturer produces devices in a budget price range, which differ in quality and a wide range of models.